View Full Version : Metal fabricator here again..
I hope I don't upset anyone, but I wanted to re-post my services. I think my initial thread didn't neccesarily get "thread Jacked", that sounds like something bad. I think it just got really long and started get into material discussion.
So, with that being said, I just wanted let everyone know that I came up with a price chart using 20g. 316 ss. It gives you an instant price including holes and notches. This should be much easier for you and I.
I will e-mail this price chart to anyone interested....
daggit
12-10-2008, 08:45 PM
are you able to supply ss tubes? prefferably ones in which one tube can fit inside another with a 1 to 2 mm clearance between the outer surface of the inner tube to the inner surface of the outer tube?
H2OPWR
12-11-2008, 01:58 AM
Just to let everyone know. Saturday night I requested a price for some specific stainless plates. I live in Alaska so it was past midnight when he received the e-mail. He responded early Sunday but I did not check until monday morning. I asked to make sure that the design was exactly like I wanted. Tuesday morning he sent me a drawing and with only one small change I sent the go ahead to this company. It is now wednesday evening and the plates are done and will be shipped tomorrow. This is OUTSTANDING SERVICE AND COMMUNICATION THANK YOU. I would recomend his services to anyone and everyone. I will do a video and show his work as soon as I receive the plates. I have not seen the quality as of yet but you usually can judge the quality by the service. I can not wait.
overtaker
12-11-2008, 11:02 AM
We always hear about the bad service. It's nice to hear about the great service! H20pwr, are the plates for a dry cell? 316l?
H2OPWR
12-11-2008, 11:32 AM
We always hear about the bad service. It's nice to hear about the great service! H20pwr, are the plates for a dry cell? 316l?
Yes, The plates are 316L for a dry cell that should have no current leakage through the holes. I will be setting up different numbers of neutral plates and testing with the same resevoir and same electrolite to measure differences in output under identical conditions.
H2OPWR
12-11-2008, 11:33 AM
I will be doing a short video as soon as I get the plates to let everyone see the quality of work.
Thank you for the compliments H20PWR, I'm just doing my job. Its too bad to hear about people ripping others off or dealing with horrible service. Quality work and a good reputation means everything! (especially in today's economy)
You should receive your plates soon, if you haven't already.
H2OPWR
12-13-2008, 10:00 PM
Thank you for the compliments H20PWR, I'm just doing my job. Its too bad to hear about people ripping others off or dealing with horrible service. Quality work and a good reputation means everything! (especially in today's economy)
You should receive your plates soon, if you haven't already.
Not here yet but I do live in Alaska and they were mailed Thursday so I don't expect them until Monday or Tuesday.
Thanks
Larry
H2OPWR
12-16-2008, 12:55 AM
The plates have arrived and to say I am very satisfied is an understatement. Take a look at the video and judge for yourself.
Thank you Tom
Larry
http://www.youtube.com/watch?v=xHwyjtUjZ9w
H2OPWR
01-02-2009, 02:11 AM
GREAT JOB!!! Thank You for your great work. Here is a video of the plates after 60 hours of run time.
http://www.youtube.com/watch?v=hT8tIn6XU7o&feature=channel_page
zennerx
01-02-2009, 03:21 PM
Anyone know where he is?
Tried contacting him more than a few times :)
Need plates!!!!
H2OPWR
01-02-2009, 03:41 PM
Anyone know where he is?
Tried contacting him more than a few times :)
Need plates!!!!
I just clicked on his name and sent him an e-mail asking for a quote. The communication was great. Just a thought he may be out for the holiday's. Keep trying his product quality is first rate as well as his prices and services.
bigjim56
01-04-2009, 12:15 AM
I sure hope he's not left, I was gonna try his work myself.
Next week should be a back to work week.
bigjim56
Yes, I am still here!
I have been sending out alot of quotes/price charts lately, so when I don't get a response I just assume the person is either not interested or is going over they're design and may get back to me eventually.:)
Painless
01-04-2009, 02:36 PM
Scm,
Why not post your price chart in a thread or this thread at post one and just keep it updated?
You would likely get more business this way.
Russ.
lowriderjj
01-04-2009, 08:26 PM
I am just trying to finalize my design before I order my plates. It's cold here in Michigan so install will have to wait for spring. Don't worry we on the forum will be supporting you!:D
H2OPWR
01-05-2009, 01:14 AM
SCM, Your plates and work have exceeded my expetations. Great Job.
Larry